搜尋結果
- Yahoo字典IPA [ɪˈpɒksi]
adj 形容詞
- 1. 環氧的 epoxy cement 環氧水泥
vt 及物動詞
- 1. 用環氧樹脂膠合
Powered by Oxford Chinese Dictionary
2007年6月30日 · Epoxy is supposedly better for gap filling (which is great for some of my joints) and one doesn't have to clamp like for Titebond. But I do know from reading and personal experience that epoxy is more susceptible to breaking from shock. I don't like the fact that the epoxy broke at the glue joint.
2012年9月1日 · 09-01-2012, 08:26 PM. Re: Epoxy FInish for Pens Etc. Ken, West System Epoxy is going to do the same thing as CA and Acrylic. West System Epoxy has a hardness of 83 (Shore) and does not reach this until after 2 weeks from the time it's cast. West System Properties.
2020年2月22日 · Hi All, I recently completed this table for my home and on other projects throughout my home I used Rubio Monocoat to make the wood grain pop. My plan was to use Rubio Monocoat on this table then epoxy flood coat the top to seal the wood. Will the Rubio Monocoat effect the epoxy resin and would the Rubio Monocoat even be
2017年1月15日 · I would use Doug's approach. With the wood shown in the pic you're going to get some bleed and discolouration no matter what method you use and whether the epoxy is tinted or not. As Jim mentioned it soaks into wood and its because of this its used to stabilize wood that is in a state of decay.
2018年7月23日 · Share. Tweet. #2. 07-22-2018, 12:02 PM. Might be a wax finish. If it is it will be difficult to get another finish to adhere to it. Polyurethane would be the best finish but you would have to remove as much of the wax as possible. Scuff the surface before coating. Good luck and let us know what happens.
2015年12月26日 · Hey Guys, New to the site and looking for some direction on how to fill some of the million little burl holes in my slab. Most of them are very dark to black in colour. What product should I use? I have seen where some guys are using the west marine epoxy system. So whatever I would use should be a dark tone to match the
2021年3月9日 · Alumilite Clear Slow - is a poly-urethane resin that should be cast under pressure, to reduce any small bubbles to un-noticeable. It all depends what it is you want to make. Personally I use Alumilite Clear Slow, and I have a Princess Auto Pressure Pot. I let my blanks sit for at least 1-2 hours at 60psi.
filling worm holes in cutting boards. 01-12-2014, 07:55 PM. I have some amazing butternut which i salvaged from our woodlot after the trees died and fell ( Butternut is a 'species at risk' under the Ontario provincial Species at Risk Act. I have made one 'cutting board' after filling the worm holes with 24 hour epoxy, planing and then applying ...
2007年11月12日 · 11-13-2007, 07:55 AM. Problem with glueing plywood faces together is that you introduce moisture to one side of the sheet and not the other. We all know what happens then. to prevent this attack of the swelling wood fibers, I would suggest you laminate with contact Cement similare to laminating Formica.
2024年2月22日 · Hey, Just finished making my owl hollowing tool. 1/2" round stock was used with a round carbide cutter. I turned a handle for it also. What's the best way to glue the the handle to the tool? I was think 5 minute epoxy should do the trick and possible cut a couple notches on the bar where it will be inside the handle for
